What Are the Best Overclock Settings for the GTX 1060? This is why in most cases, the card reaches a maximum of 2 or 2.1 GHz and stays stable thanks to the GTX 1060 boost feature. Things like voltage, power, load, and limiters will alter the maximum clock state. Keep in mind that your card’s frequency is never fixed because of the boost clock’s dynamic nature. If it doesn’t fail or crashes, you’ve successfully done a GTX 1060 overclock. Once you get a good, stable overclock, stress-test the GPU again with Furmark for a couple of hours.
#Msi afterburner gtx 1060 full#
In the case of the latter, you’ll have to restart the card to get the full speed again. Keep in mind that if you overclock too much, your screen will go black, and your GPU’s clock will fall down to a very low frequency to prevent damage. Generally, you can get a 100-150 MHz boost for the GPU core and a 200-250 MHz boost for the VRAM while staying within a stable operating temperature. This will give you a value where you can run your card comfortably without worrying about crashes or glitches. Once you start getting artifacts, reduce the core offset back to the most stable value.
#Msi afterburner gtx 1060 software#
If your card hasn’t reached the thermal limit, go ahead and boost the core clock in small increments of 50 MHz.Ĭontinue doing so until you get artifacts (flashes or pops on the screen that definitely shouldn’t be there) or your card reaches the thermal limit.Īlso, make sure that you continue to perform some stress tests in between the changes using software like 3D Mark. At the same time, don’t forget to monitor the temperature. While doing so, keep an eye on your clock and how much it boosts. Start by increasing the power to the maximum that your graphics card software (like Afterburner) will allow you to. Just like the 1080Ti discussed above, the Nvidia GeForce GTX 1060 is also a pascal card, and the way to overclock it is also quite similar. So, the bottom line is that you’re limited by power and thermal limits. The same is the case if you try a 200 MHz offset. If you now increase the clock rate by 150 MHz, it will reach 2020 MHz, but because of thermal limits, it will come back down to 1950 MHz. Note that no direct clock offset has been made yet. Now, if you also set the fan to 100%, the card will hit as high as 1910 MHz. Without turning on the OC Mode, the card can easily go up to 1700 MHz, which is more than the listed boost clock rate.Īnd if you turn the OC Mode on and only raise the power to the maximum limit (120% in this case), the boost clock rate will go up to 1890 MHz. The Asus GTX1080Ti (also a Pascal card) lists a boost clock of 1683 MHz and 1780 MHz in its OC Mode. And as long as the GPU is not limited by power or heat, it will continue to boost the clock. Pascal also introduced the GPU Boost 3, which, if you really consider it, also overclocks the GPU. If you really want to increase the temperature, you will have to physically modify your card. With Maxwell, you couldn’t adjust the core voltage of the GPU, and with Pascal, it’s almost impossible to provide too much voltage to the core.
Since the introduction of Pascal (the GPU architecture that powers the 1060), it has become really hard to burn your Nvidia graphics card when performing basic overclocking. Generally, you can increase the VRAM clocks more than you can increase the core, but a significant increase in the latter can also cause the system to crash instantly.īut overclocking the card is not that simple, and to better understand how you can do it, let’s get a few things out of the way first. If it stays stable for around 10 minutes, increase the clock by 10-25 MHz and run the tests again. To overclock the GTX 1060, start by increasing the VRAM and GPU by a small amount, like 50 MHz, and do a stress test using software like Furmark. – How Much Performance Boost Can You Get From a GTX 1060 Overclock?.– Zotac GTX 1060 6GB Overclock Settings.– Gigabyte GTX 1060 6GB Overclock Settings.
0 kommentar(er)
